Pierre de Smet, President of Dynalog, Inc. with offices located in Bloomfield Hills, Oakland County,
Michigan was just awarded a certificate of appreciation in recognition of his continued participation for the past five years on the
Industrial Advisory Board at Lawrence Technological University.
Dynalog's IdentiCal system has been selected by a Japanese robot manufacturer for calibration of their
robots. The IdentiCal system is utilized to identify the robot's zero-position mastering, which is updated in the robot
controller before the robot is shipped to their customer.
July 25, 2018: Trade Show
Along with our Chinese distributor, Worldwide
Technologies, we displayed our products at the China International Robot Show (CIROS) in Shanghai, China. Click
here to read the news
release.
July 2, 2018: China International Robot Show 2018
Dynalog will participate in the China International Robot Show (CIROS)
2018, which takes place from July 4th to July 7th, 2018, in Shanghai. Worldwide Technologies, Dynalog's distributor in China, will
present Dynalog products: the DynaCal™ robot-cell calibration system, the AutoCal™ (TCP + robot) recovery system, the AccuBeam™ robot
temperature compensation system, the DynaGuide™ robot adaptive control and guidance system, the DynaFlex™ robot gauging system, and
the CompuGauge™ robot performance analysis system. Visit this link for more information:
http://en.ciros.com.cn. We look forward to
meeting with you at this event.
May 14, 2018: A Japanese Auto Maker Selects Dynalog's DynaCal System
Dynalog's Dynacal system has
been selected by a Japanese auto maker in the US for recovery of their robot programs after a crash, moved fixture, replacement of
robot motors, and replacement of end-effector. A reference signature of the robot-cell is acquired with the DynaCal system when the
robot-cell is performing its production job accurately. After a change in the robot-cell, e.g. tool crash, the DynaCal system is utilized
to identify the difference in the robot-cell signature compared to the reference signature. The differences are updated in the robot
controller, i.e. TCP, User Frame, and Zero-Position-Mastering are updated in the robot controller, which recovers the robot programs
to its previous accurate state.
November 14, 2017: An American Aeronautic System Integrator Selects Dynalog's DynaCal System
Dynalog's
Dynacal system has been selected by an American aerospace system integrator to provide robot-cell Absolute Accuracy and to enable
off-line programming for their robotic drilling cells installed in their Mexican plant. The integrator uses the DynaCal system to
identify the Absolute Accuracy parameters of the robot-cell. Furthermore, with the identified robot-cell parameters, the DynaCal Filter
Module compensates the robot positions created in a simulation environment to account for the differences between the simulation robot-cell
and the actual robot-cell. The precision provided by the calibrated robot-cell meets the requirements of their robotic drilling process.
June 1, 2017: China International Robot Show 2017
Dynalog will participate in the China International Robot Show (CIROS) 2017, which
takes place from July 5th to July 8th, 2017, in Shanghai. Worldwide Technologies, Dynalog's distributor in China, will present Dynalog
products: the DynaCal™ robot-cell calibration system, the AutoCal™ (TCP + robot) recovery system, the AccuBeam™ robot temperature
compensation system, the DynaGuide™ robot adaptive control and guidance system, the DynaFlex™ robot gauging system, and the CompuGauge™
robot performance analysis system. Visit this link for more information:
http://en.ciros.com.cn. We look forward to meeting with you
at this event.
May 11, 2017: Trade Show
Dynalog will participate in the trade show Metalloobrabotka 2017, which takes place from May
15th to May 19th, 2017, in Moscow. Master-Service Metrology Group, Dynalog's distributor in Russia, will present Dynalog products:
the DynaCal™ robot-cell calibration system, the AutoCal™ (TCP + robot) recovery system, the AccuBeam™ robot temperature compensation
system, the DynaGuide™ robot adaptive control and guidance system, the DynaFlex™ robot gauging system, and the CompuGauge™ robot performance
analysis system. Visit this link for more information:
https://www.metobr-expo.ru/en/. Come visit us at booth #FF108. We look forward
to meeting with you at this event.
March 01, 2017: A Global Automaker Selects Dynalog for Robotic Accuracy for their Laser Cutting
Application
Dynalog is selected by a global automaker to provide Absolute Accuracy, Temperature Compensation, and Guidance for robots
performing laser cutting process. A robot-mounted sensor is utilized to acquire the calibration and guidance measurements. A robot-mounted
sensor reduces the number of sensors required to perform the robot guidance process. These laser cutting cells will soon go into full
production.
Ceramic based calibration targets are mounted within the robot-cells. The measurements of the calibration targets are
utilized by Dynalog's DynaFlex software to identify the Absolute Accuracy robot-cell parameters. Furthermore, periodic measurements
of the calibration targets are obtained automatically (few measurements during transfer of the car), and used to identify the change
in the robot-cell parameters. The critical robot laser cutting positions are compensated for the change in the robot-cell parameters.
Moreover, during each production cycle a few car datum features are measured by the robot-mounted sensor. The accurate location of
the car is identified based on these measurements.
November 09, 2016: Trade Show
Along with our Chinese distributor, Worldwide Technologies,
we displayed our products at the CIFF Expo in Shanghai, China. Click
here to read the news release.
October 18, 2016: Research Study
of Absolute Accuracy of Robots Using Dynalog's CompuGauge System
Polytechnica University of Romania conducted a research study to
determine the Absolute Accuracy of Industrial robots using the performance analysis module of Dynalog's CompuGauge system. The CompuGauge
performance analysis module is based on ISO-9283 and ANSI RIA 15.05 standards. The results of the study is available at the following
link:
http://www.wseas.us/e-library/conferences/2013/Vouliagmeni/MRME/MRME-08.pdf.
October 5, 2016: Ford Selects AccuBeam System for
Robot Temperature Compensation
Ford has selected Dynalog's AccuBeam robot temperature compensation system for many of its high precision
robotic-based applications, e.g. laser cutting, form & pierce, etc., that are being installed in various plants around the world.
The AccuBeam system automatically compensates for robot drift due to changes in ambient temperature, and due to self-heating, thus
maintaining the robot's repeatability over-time. The AccuBeam system is a proven production ready in-line system that has been successfully
compensating robots for more than10 years. The AccuBeam system includes the required automatic communication with the robot controller,
the AccuBeam sensor, and other peripheral equipment. Click the following link to view the AccuBeam product data sheet: AccuBeam.
July
11, 2016: Trade Show
Along with our Chinese distributor, Worldwide Technologies, we displayed our products at the CIROS International
Robot Show in Shanghai, China. Click
here to read the news release.
May 5, 2016: Adaptive Control of Robot for Aerospace Drilling
Dynalog is chosen by an aerospace integrator to provide accuracy solution for two robots performing drilling and routing of their
parts. The DynaGuide Adaptive Control system performs automatic in-line compensation of the robot's position based on measurements
of the TCP from a Northern Digital photogrammetry system. The robot-cell contains two Fanuc robots on 20 meters long tracks. Two photogrammetry
systems are used by the DynaGuide software to automatically monitor and correct the TCP(xyz & orientation) of both the robots.
Dynalog's DynaCal system provides the initial robot-cell Absolute Accuracy required to reduce the number of corrective iterations
performed by the DynaGuide Adaptive Control system. Furthermore, Dynalog's AutoCal system is also used to monitor and recover the
robots TCP and zero-position-mastering for changes due to e.g. crash, change of motors, replacement of end-effector, etc. The achieved
robotic drilling position accuracy is only limited by the accuracy of the measurement system and the resolution of the robot. Click
the following links to view the product data sheets: DynaCal, DynaGuide, and AutoCal.